Modification of graphene oxide and its effect on properties of natural rubber/graphene oxide nanocomposites

• Nghiem Thi Thuong,
• Le Dinh Quang,
• Vu Quoc Cuong,
• Cao Hong Ha,
• Nguyen Ba Lam and
• Seiichi Kawahara

Beilstein J. Nanotechnol. 2024, 15, 168–179, doi:10.3762/bjnano.15.16

• also attracted significant interest. This material with exceptionally high specific surface area, high mechanical properties, and high thermal conductivity is expected to prepare high-performance rubber composites [21][22][23]. In our recent work [24], we successfully designed a DPNR/GO composite by

Experimental investigation of usage of POE lubricants with Al₂O₃, graphene or CNT nanoparticles in a refrigeration compressor

• Kayhan Dağıdır and
• Kemal Bilen

Beilstein J. Nanotechnol. 2023, 14, 1041–1058, doi:10.3762/bjnano.14.86

• nanoparticles at different concentrations. They found that the addition of nanoparticles enhanced the thermophysical properties and heat transfer characteristics of the lubricant. The researchers specified that nanolubricants typically provide greater thermal conductivity and viscosity in comparison to pure

• lubricants [2]. Sanukrishna and Prakash [3] experimentally investigated the thermophysical properties of a nanolubricant containing TiO2 nanoparticles for volume fractions of 0.07 to 0.8% in a temperature range of 20 to 90 °C. The results showed that the thermal conductivity and viscosity of the

• that the thermal conductivity and viscosity of the nanolubricant increased with the increase in mass fraction at a constant temperature. This capability in thermal conductivity enhancement can aid in addressing heat transfer issues within systems. Due to the fact that heat transfer takes place at the

A graphene quantum dots–glassy carbon electrode-based electrochemical sensor for monitoring malathion

• Sanju Tanwar,
• Aditi Sharma and
• Dhirendra Mathur

Beilstein J. Nanotechnol. 2023, 14, 701–710, doi:10.3762/bjnano.14.56

• application of electrochemical methods in detection of pesticides has already been extensively studied [9][10][11][12][13]. Nanomaterials are ideal for electrochemical sensing because of their unique properties such as high chemical stability, thermal conductivity, electrical conductivity, and large surface

Titania nanoparticles for photocatalytic degradation of ethanol under simulated solar light

• Evghenii Goncearenco,
• Iuliana P. Morjan,
• Claudiu Teodor Fleaca,
• Florian Dumitrache,
• Elena Dutu,
• Monica Scarisoreanu,
• Valentin Serban Teodorescu,
• Alexandra Sandulescu,
• Crina Anastasescu and
• Ioan Balint

Beilstein J. Nanotechnol. 2023, 14, 616–630, doi:10.3762/bjnano.14.51

• AM 1.5 solar light (1000 W/m2) was provided by a Peccell L01 solar simulator. For each test, 200 µL gas samples were taken from the photoreactor every 30 min and analyzed with two gas chromatographs equipped with either a flame ionization detector (FID, Agilent 7890A) or a thermal conductivity

Thermal transport in kinked nanowires through simulation

• Alexander N. Robillard,
• Graham W. Gibson and
• Ralf Meyer

Beilstein J. Nanotechnol. 2023, 14, 586–602, doi:10.3762/bjnano.14.49

• Fourier model. Keywords: ballistic transport; kinked nanowire; molecular dynamics; phonon Monte Carlo; thermal transport; Introduction The thermal conductivity of semiconductor nanostructures is of great interest because of potential applications in a wide variety of fields, such as thermal control

• for unfettered ballistic phonon transit, suppressing the contribution to thermal transport. Heron et al. [23] found that nanowires with square serpentines with dimensions of a few hundred nanometers exhibit reductions in thermal conductivity of the order of 20–40%. Zhang et al. found that, in boron

• transport, thus reducing the conductance (or equivalently, increasing the thermal resistance) for the same temperature difference. Works on serpentine nanowires show similar behaviour [22], with thermal conductivity asymptotically approaching a constant (which is analogous to an inverse proportionality for

On the use of Raman spectroscopy to characterize mass-produced graphene nanoplatelets

• Keith R. Paton,
• Konstantinos Despotelis,
• Naresh Kumar,
• Piers Turner and
• Andrew J. Pollard

Beilstein J. Nanotechnol. 2023, 14, 509–521, doi:10.3762/bjnano.14.42

• materials [5], offering an array of products with a wide range of properties such as improved mechanical strength and higher thermal conductivity. To accelerate the further development and adoption of GR2Ms, it is critical to develop reliable and standardized methods to characterize the materials being

Molecular nanoarchitectonics: unification of nanotechnology and molecular/materials science

• Katsuhiko Ariga

Beilstein J. Nanotechnol. 2023, 14, 434–453, doi:10.3762/bjnano.14.35

• both metallic and semiconducting properties. These networks have been applied to thermoelectric materials and have been found to exhibit low interplane thermal conductivity, which is not typical of carbon materials, while maintaining the interplane electrical conductivity. Müllen, Fuchs, Chi, and co

Plasmonic nanotechnology for photothermal applications – an evaluation

• A. R. Indhu,
• L. Keerthana and
• Gnanaprakash Dharmalingam

Beilstein J. Nanotechnol. 2023, 14, 380–419, doi:10.3762/bjnano.14.33

• specific heat, k is the thermal conductivity, T is the temperature, t is the time, and is the rate of heat generation (or depletion) per unit volume. The Laplacian ∇2 represents the temporal change in the temperature variation of the material. The rate of heat generation or depletion, , is arrived at from

• volume fraction of the particles, Tm is the melting temperature, Tc is the temperature of the cooling fluid, W is the thickness of the compartment holding the n-PCM, kw is the conductivity of the wall, and k′ is the conductivity of the PCM. The thermal conductivity of the plasmonically enhanced PCM

• thermal conductivity and absorption power of the surrounding medium. The temperature increase in the metal nanoparticles (ΔTNP) and thermal capacitance coefficient can be calculated using the following equation [96]: I is the illumination intensity of the laser source, σabs is the absorption cross section

A cantilever-based, ultrahigh-vacuum, low-temperature scanning probe instrument for multidimensional scanning force microscopy

• Hao Liu,
• Zuned Ahmed,
• Sasa Vranjkovic,
• Manfred Parschau,
• Andrada-Oana Mandru and
• Hans J. Hug

Beilstein J. Nanotechnol. 2022, 13, 1120–1140, doi:10.3762/bjnano.13.95

• nitrogen (LN2) container and an additional heat shield, which is passively cooled by the evaporating He gases of the LHe tank (Figure 2a). The microscope is surrounded by two shields (a Au-plated oxygen-free high thermal conductivity (OFHC) copper LHe shield and an Al LN2 shield) of which there is an inner

Comparative molecular dynamics simulations of thermal conductivities of aqueous and hydrocarbon nanofluids

• Adil Loya,
• Antash Najib,
• Fahad Aziz,
• Asif Khan,
• Guogang Ren and
• Kun Luo

Beilstein J. Nanotechnol. 2022, 13, 620–628, doi:10.3762/bjnano.13.54

• experimental data. Highly concurrent trends were achieved for the obtained results. According to the obtained results of MDS, adding CuO nanoparticles increased the thermal conductivity of water by 25% (from 0.6 to 0.75 W·m−1·K−1). However, by adding these nanoparticles to hydrocarbon-based fluids (i.e

• ., alkane) the thermal conductivity was increased three times (from 0.1 to 0.4 W·m−1·K−1). This approach to determine the thermal conductivity of metal oxide nanoparticles in aqueous and nonaqueous fluids using visual molecular dynamics and interactive autocorrelations demonstrate a great tool to quantify

• thermophysical properties of nanofluids using a simulation environment. Moreover, this comparison introduces data on aqueous and nonaqueous suspensions in one study. Keywords: alkanes; aqueous solutions; CuO; hydrocarbon solutions; molecular dynamics simulation; nanoparticles; thermal conductivity

Design aspects of Bi₂Sr₂CaCu₂O_8+δ THz sources: optimization of thermal and radiative properties

• Mikhail M. Krasnov,
• Natalia D. Novikova,
• Roger Cattaneo,
• Alexey A. Kalenyuk and
• Vladimir M. Krasnov

Beilstein J. Nanotechnol. 2021, 12, 1392–1403, doi:10.3762/bjnano.12.103

• large crystals, requiring more epoxy, this is more difficult and the remaining epoxy layer is usually thicker. For this reason we assume the epoxy thickness de = 1 μm for whisker and de = 5 μm for crystal-based devices. The monocrystalline sapphire substrate has a very good thermal conductivity, κ, at

Irradiation-driven molecular dynamics simulation of the FEBID process for Pt(PF₃)₄

• Alexey Prosvetov,
• Alexey V. Verkhovtsev,
• Gennady Sushko and
• Andrey V. Solov’yov

Beilstein J. Nanotechnol. 2021, 12, 1151–1172, doi:10.3762/bjnano.12.86

• atomistic level although it governs many physical properties such as electrical and thermal conductivity, and magnetic properties [27][28]. Atomistic simulations provide insights into the internal structure of the deposits and its evolution depending on the regimes of the FEBID process. In this study

First-principles study of the structural, optoelectronic and thermophysical properties of the π-SnSe for thermoelectric applications

• Muhammad Atif Sattar,
• Najwa Al Bouzieh,
• Maamar Benkraouda and
• Noureddine Amrane

Beilstein J. Nanotechnol. 2021, 12, 1101–1114, doi:10.3762/bjnano.12.82

• is exceptionally promising for the next generation of photovoltaic and thermoelectric devices at room and high temperatures. Keywords: density functional theory (DFT); electronic properties; lattice thermal conductivity; optical properties; thermodynamic properties; thermoelectric properties; tin

• conductivity, thermal conductivity, electronic thermal conductivity, lattice thermal conductivity, and absolute temperature, respectively [5]. The bottleneck that limits the extensive use of TE materials is their relatively low value of ZT. The close interdependency of the three entities S, σ, and κtot offer

• the power factor (PF = S2σ) which is connected with the electrical transport [8][9] and the lowest value of κtot [10]. To date, a considerable amount of research has been performed to enhance the ZT value. For instance, by lowering the value of the lattice thermal conductivity (through all-scale

A review of defect engineering, ion implantation, and nanofabrication using the helium ion microscope

• Frances I. Allen

Beilstein J. Nanotechnol. 2021, 12, 633–664, doi:10.3762/bjnano.12.52

• properties Further defect engineering studies using the HIM have been concerned with tuning the thermal properties of materials. The first example of this demonstrated site-selective engineering of thermal conductivity along the length of individual nanowires [70]. Here, Zhao et al. irradiated discrete

• sections of free-standing crystalline silicon nanowires of 160 nm diameter to a series of target doses. It was found that a dramatic decrease in thermal conductivity occurred already at relatively low doses, corresponding to point defect concentrations of only a few percent. This result indicated a strong

• phonon scattering effect from the few point defects introduced. For higher doses above ca. 2 × 1016 ions/cm2, complete amorphization of the material occurred, although it was noted that the overall morphology of the structure was unaffected. This ability to locally tune the thermal conductivity by

A review on the green and sustainable synthesis of silver nanoparticles and one-dimensional silver nanostructures

• Sina Kaabipour and
• Shohreh Hemmati

Beilstein J. Nanotechnol. 2021, 12, 102–136, doi:10.3762/bjnano.12.9

• characteristics including antimicrobial activity, electrical conductivity, thermal conductivity, optical characteristics, and mechanical properties. The antimicrobial characteristic of silver nanoparticles (AgNPs) has made them highly applicable in the biomedical and therapeutic fields [69][70][71]. Currently

• infections, and also inhibit the growth of bacterial biofilms [14][15][16]. AgNPs were also used in developing strong thermally conductive materials. They were used in polymer composites to increase thermal conductivity (K) [77][78] for cooling applications in electronic equipment. Furthermore, AgNPs have

Imaging and milling resolution of light ion beams from helium ion microscopy and FIBs driven by liquid metal alloy ion sources

• Nico Klingner,
• Gregor Hlawacek,
• Paul Mazarov,
• Wolfgang Pilz,
• Fabian Meyer and
• Lothar Bischoff

Beilstein J. Nanotechnol. 2020, 11, 1742–1749, doi:10.3762/bjnano.11.156

• ], the fabrication of graphene nanomeshes [8], the formation of single Si nanocrystals embedded in SiO2 for single-electron transistors [9], the spatially resolved engineering of the thermal conductivity in individual Si nanowires [10], as well as the creation of nano-Josephson superconducting tunnel

Seebeck coefficient of silicon nanowire forests doped by thermal diffusion

• Shaimaa Elyamny,
• Elisabetta Dimaggio and
• Giovanni Pennelli

Beilstein J. Nanotechnol. 2020, 11, 1707–1713, doi:10.3762/bjnano.11.153

• conductivity of nanostructures, will yield a high efficiency of the conversion of thermal to electrical energy. Keywords: nanowires; Seebeck coefficient; thermal conductivity; thermoelectricity; Introduction Thermoelectric generators for direct conversion of heat into electrical power will certainly play a

• sustainable. Silicon has a very high power factor S2σ [1][2][3][4] (S is the Seebeck coefficient and σ is the electrical conductivity). This, combined with the reduced thermal conductivity when nanostructured [5][6][7][8][9][10], makes it very suitable for thermoelectric applications. As added value, silicon

• require an oxidation of the surface for the trapping of the doping species. However, the reduction of the thermal conductivity, which is the aim of the nanoscale structuring, relies on the roughness of the nanowire surfaces, and the smoothing produced by the oxide growth would heavily reduce this effect

Detecting stable adsorbates of (1S)-camphor on Cu(111) with Bayesian optimization

• Jari Järvi,
• Patrick Rinke and
• Milica Todorović

Beilstein J. Nanotechnol. 2020, 11, 1577–1589, doi:10.3762/bjnano.11.140

• been applied in detecting molecular conformers [25] and adsorbate structures [26][27], in identifying stable molecular compounds [28], and in discovering materials with low thermal hysteresis [29] or thermal conductivity [30]. Typically, previous studies have employed customized material-specific

Nonadiabatic superconductivity in a Li-intercalated hexagonal boron nitride bilayer

• Kamila A. Szewczyk,
• Izabela A. Domagalska,
• Artur P. Durajski and
• Radosław Szczęśniak

Beilstein J. Nanotechnol. 2020, 11, 1178–1189, doi:10.3762/bjnano.11.102

• result is radically different from the data obtained for graphene/SiO2 [33]. In addition, hBN monolayers exhibit a high temperature stability, a low dielectric constant (ε = 3–4), and a high thermal conductivity [34]. The band gap of hBN is about 5.9 eV [35]. Furthermore, which is also important, hBN is

Thermophoretic tweezers for single nanoparticle manipulation

• Jošt Stergar and
• Natan Osterman

Beilstein J. Nanotechnol. 2020, 11, 1126–1133, doi:10.3762/bjnano.11.97

•  1b,c). Temperature measurements are performed using the temperature-dependent fluorescence of sulforhodamine B (Radiant dyes Chemie), which is calibrated in an independent measurement (accuracy ±2 K). Since the sapphire glass with a high thermal conductivity helps cooling the thin sample film, the

Effect of magnetic field, heat generation and absorption on nanofluid flow over a nonlinear stretching sheet

• Santoshi Misra and
• Govardhan Kamatam

Beilstein J. Nanotechnol. 2020, 11, 976–990, doi:10.3762/bjnano.11.82

• thermal conductivity and convective heat transfer performance of base fluids such as water, ethylene, glycol, etc. This takes place due to the intense and rigorous distribution of nanoparticle Brownian motion within the base fluid, thus enhancing the uniformity, conductance and properties which have paved

Light–matter interactions in two-dimensional layered WSe₂ for gauging evolution of phonon dynamics

• Avra S. Bandyopadhyay,
• Chandan Biswas and
• Anupama B. Kaul

Beilstein J. Nanotechnol. 2020, 11, 782–797, doi:10.3762/bjnano.11.63

• external stimuli. For example, external radiation could be in the form of heat or optical energy, which also directly influences properties such as the electronic and optoelectronic transport and the thermal conductivity of the material. In this work, we have conducted an in-depth analysis of the phonon

• dependence of the Raman shifts in 2D TMDCs such as MoS2 [20][21][22][23][24], and WS2 [25][26] have been extensively studied over a wide temperature range from which properties such as thermal conductivity was deciphered [23][27]. On the contrary, the temperature-dependent Raman analysis of WSe2 is rather

• phonon density increases as T3, while in a quantum confined system such as the 1L case, the phonon density is not as strong a function of T. This also has a direct influence on the thermal conductivity of quantum-confined 1D structures where the thermal conductivity should be high and not vary

An advanced structural characterization of templated meso-macroporous carbon monoliths by small- and wide-angle scattering techniques

• Felix M. Badaczewski,
• Marc O. Loeh,
• Torben Pfaff,
• Dirk Wallacher,
• Daniel Clemens and
• Bernd M. Smarsly

Beilstein J. Nanotechnol. 2020, 11, 310–322, doi:10.3762/bjnano.11.23

• structures [51][52][53][54]. Key properties of glassy carbon materials, such as thermal conductivity, chemical resistance, hardness, density, and coefficient of thermal expansion are closely related to the carbon microstructure and the porosity. Resin-based carbon materials are known to possess a substantial

Size effects of graphene nanoplatelets on the properties of high-density polyethylene nanocomposites: morphological, thermal, electrical, and mechanical characterization

• Tuba Evgin,
• Alpaslan Turgut,
• Georges Hamaoui,
• Zdenko Spitalsky,
• Nicolas Horny,
• Matej Micusik,
• Mihai Chirtoc,
• Mehmet Sarikanat and
• Maria Omastova

Beilstein J. Nanotechnol. 2020, 11, 167–179, doi:10.3762/bjnano.11.14

• percolation threshold than thicker ones. On the other hand, in terms of thermal conductivity, a remarkable amount of enhancement was observed only above a certain filler concentration. The results demonstrate that GnPs with smaller lateral size and larger thickness lead to lower enhancement of the samples

• in more contact with each other. It is obvious from Figure 1 that G2 could form filler networks more easily than G1 and G3. From this study, it can be proposed that HDPE-based nanocomposites with G2 may show a greater number of GnP pathways and consequently higher electrical and thermal conductivity

• the aspect ratio of the GnPs [28]. However, the aspect ratio was not the only important parameter. As described by Horny and co-workers [29], for a given lateral size, an optimal thickness exists that gives the highest thermal conductivity. It could be assumed that this is also valid for electrical

Influence of the epitaxial composition on N-face GaN KOH etch kinetics determined by ICP-OES

• Markus Tautz,
• Maren T. Kuchenbrod,
• Joachim Hertkorn,
• Robert Weinberger,
• Martin Welzel,
• Arno Pfitzner and
• David Díaz Díaz

Beilstein J. Nanotechnol. 2020, 11, 41–50, doi:10.3762/bjnano.11.4

• epitaxy stack. Thin-film technology is a common approach in industry to improve device performance. Thereby, a substrate with higher thermal conductivity, e.g., silicon or nickel, is bonded to the top p-contact of the LED structure [8]. The sapphire substrate is removed by laser lift off (LLO). This